WDAP-8350

600Mbps Dual Band 802.11n Outdoor Wireless CPE (IP66, 802.3at PoE, 4 x N-Type connector)

Powerful Dual-Band Outdoor WLAN Solution
PLANET WDAP-8350 comes with a high transmission power of 500mW which can bridge two remote nodes in the5GHz frequency band and provides clients with 2.4GHz wireless access over longer distance range. Its fully-protected hardware design makes it capable to ward off direct lightning strikes and unpredictable harsh weathers. Furthermore, the WDAP-8350 adopts the high-class Qualcomm Atheros SoC (System-on-a-Chip) and Dual-OS Backup mechanism that provide higher stability to meet the stringent requirements of outdoor solution.
More Flexible for Outdoor Environments
With its dual-RF design and by connecting optional specific types and higher gain antennas to its N-Type antenna connectors, the WDAP-8350 can adapt to various applications including connecting IP cameras at multiple locations to the security control center to deploy a surveillance system, or relaying the wireless signal from the urban to the suburban to provide wireless internet service to rural residents simultaneously. With the WDAP-8350, an outdoor wireless infrastructure can be speedily deployed, thus realizing the setting up of an outdoor, long-distance, dual-purpose unit.
All-Weather Rugged Protection
With the IP66-rated aluminum housing, Surge Arrester, Heater design and wide-ranging operating temperature from -40 to 70 degrees C, PLANET WDAP-8350 can perform normally under rigorous weather conditions, including thunderstorms, and hot and cold climates, thus maintaining the connection as stable as that in the general environments.
Seamless Failover and Roaming
In the actual user experience, a redundant setup is important in that,the WDAP-8350 enables the auto failover mechanism to activate by using dual images (Dual-OS) while if the active OS fails, it can immediately switch to the standby OS. That can eliminate the difficulty of real-time support in long distance and make failover as simple as possible. Furthermore, it enhances handover of clients between APs by improving the handshaking process to promote better performance, thus reducing the handoff times between APs and associated clients, which means it can quickly handover to the nearby AP without any disconnection. Benefiting from the auto-backup and fast roaming, the WDAP-8350 is able to achieve a non-disruptive path failover and seamless roaming.
High-efficiency and Practical Solution to Separate Various Applications
PLANET WDAP-8350 supports multiple SSIDs (16 sets of SSIDs for each band) to allow each virtual wireless network to have a different set of security and also is capable to map each VAP to a specific virtual network through the use of VLAN tagging which enables isolation of guest and corporate networks. In addition, its dynamic rate adaptation mechanism for multicast guarantees the wireless bandwidth and service quality or the fixed rate of video streaming, which prevents from capacity wasting of multicast packets, thus utilizing the available bandwidth with more efficiency.
Advanced Value-added Characteristics
Featuring an IPv4/IPv6 dual-stack network, the WDAP-8350 can work with the original IPv4 network structure and also support the cutting-edge IPv6 network, which provides migration from the IPv4 to IPv6 network with ease. With the dynamic power saving mode implementation, it is capable to detect the traffic loading, which consumes low standby power automatically, thus reducing power consumption by less than 30%.
Easy Deployment and Management
Compliant with IEEE 802.3at PoE+ (Power over Ethernet) standard, the WDAP-8350 can be powered by a single UTP cable besides providing data transmission. It thus reduces the needs of extra cables and dedicated electrical outlets which are difficult to reach in outdoor environment. It enables the wireless LAN deployment to become more flexible and worry-free from the power outlet locations. Moreover, with the Planet Smart Discovery Utility, the WDAP-8350 is convenient to be configured remotely and with the Wireless Location Management, it is easy to locate online clients’ information.
Ordering Information
WDAP-8350 600Mbps Dual Band 802.11n Outdoor Wireless CPE (IP66, 802.3at PoE, 4 x N-Type connector)
Accessories
CB-STP-25 25-meter STP Cat5 Cable
WL-NM-0.6 0.6-meter N-male (male pin) to N-male (male pin) Cable
ANT-OM5D 2.4/5GHz Dual Band Omni-directional Antenna
ANT-OM8 2.4GHz 8dBi Omni Directional Antenna
ANT-OM15 2.4GHz 15dBi Omni Directional Antenna
ANT-FP9 2.4GHz 9dBi Flat Panel Directional Antenna
ANT-FP14D 2.4GHz 14dBi Flat Panel Dual Polarization Directional Antenna
ANT-FP18 2.4GHz 18dBi Flat Panel Directional Antenna
ANT-SE18 2.4GHz 12-18dBi Adjustable Sector Antenna
ANT-YG13 2.4GHz 13dBi Yagi Directional Antenna
ANT-YG20 2.4GHz 20dBi Yagi Directional Antenna
ANT-GR21 2.4GHz 21dBi Grid Directional Antenna
ANT-OM10A 5GHz 10dBi Omni-directional Antenna
ANT-FP14AD 5GHz 14dBi Flat Panel Dual Polarization Directional Antenna
ANT-FP18A 5GHz 18dBi Flat Panel Antenna
ANT-FP23A 5GHz 23dBi Flat Panel Directional Antenna
ANT-SE17A 5GHz 16.5dBi Sector Antenna
ANT-SE21A 5GHz 21dBi Sector Antenna
Perfect Dual-Band Infrastructure and Flexible Antenna Combination
With high-power, long-distance, reliable and comprehensive characteristics, the WDAP-8350’s durable and robust hardware design, and dramatic wireless efficiency are perfect for any outdoor network infrastructure. By connecting optional specific types and higher gain antennas to functioning with its dual RF design, the WDAP-8350 can adapt to various applications. For example, it establishes the backhaul link through the 5GHz RF interface and relays the wireless signal through the 2.4GHz interface to provide internet service to rural residents simultaneously. With the WDAP-8350, an outdoor wireless infrastructure in a harsh environment can be speedily deployed to save cost and time.
**To get the best results, matching the WDAP-8350 with our related products is recommended.
Ordering Information
WDAP-8350 600Mbps Dual Band 802.11n Outdoor Wireless CPE (IP66, 802.3at PoE, 4 x N-Type connector)
Accessories
CB-STP-25 25-meter STP Cat5 Cable
WL-NM-0.6 0.6-meter N-male (male pin) to N-male (male pin) Cable
ANT-OM5D 2.4/5GHz Dual Band Omni-directional Antenna
ANT-OM8 2.4GHz 8dBi Omni Directional Antenna
ANT-OM15 2.4GHz 15dBi Omni Directional Antenna
ANT-FP9 2.4GHz 9dBi Flat Panel Directional Antenna
ANT-FP14D 2.4GHz 14dBi Flat Panel Dual Polarization Directional Antenna
ANT-FP18 2.4GHz 18dBi Flat Panel Directional Antenna
ANT-SE18 2.4GHz 12-18dBi Adjustable Sector Antenna
ANT-YG13 2.4GHz 13dBi Yagi Directional Antenna
ANT-YG20 2.4GHz 20dBi Yagi Directional Antenna
ANT-GR21 2.4GHz 21dBi Grid Directional Antenna
ANT-OM10A 5GHz 10dBi Omni-directional Antenna
ANT-FP14AD 5GHz 14dBi Flat Panel Dual Polarization Directional Antenna
ANT-FP18A 5GHz 18dBi Flat Panel Antenna
ANT-FP23A 5GHz 23dBi Flat Panel Directional Antenna
ANT-SE17A 5GHz 16.5dBi Sector Antenna
ANT-SE21A 5GHz 21dBi Sector Antenna
Industrial-grade Wireless LAN
  • Compliant with IEEE 802.11n 2T2R MIMO with backward compatible with 802.11a/b/g standard
  • Simultaneous 2.4GHz and 5GHz wireless connectivity
  • Equipped with Gigabit LAN and 600Mbps wireless connectivity (Dual-N Band)
  • IPv4 and IPv6 dual-stack management networks

Radio and Outdoor Characteristics
  • Built-in 4 N-Type (Female) antenna connectors
  • High output power of up to 500mW with multiple adjustable transmit power control
  • Built-in surge arrester and ground terminal for protection against lightning strikes
  • IP66 aluminum case
  • IEEE 802.3at PoE design
  • Wide operating temperature of -40 ~ 70 degrees C

Wireless Characteristics
  • Dual-N band performs backhaul WDS link at 5GHz and relay wireless signal at 2.4GHz
  • Multiple wireless modes: AP, WDS PtP and WDS PtMP
  • Supports up to 16 multiple-SSIDs at each frequency band
  • Multicast rate adaptation guarantees wireless bandwidth and service quality
  • Automatic ACK timeout detection for long-range connection

Secure and Highly-reliable Network Management
  • Advanced 128-bit WEP, WPA/WPA2, WPA-PSK/WPA2-PSK(TKIP/AES) security, and 802.1x authentication
  • Supports IEEE 802.1Q tagged VLAN over WDS or mapping up to 32 SSIDs
  • Dual-image (dual-OS) backup mechanism
  • Easy Web-based UI and PLANET Smart Discovery supported
  • Telnet command line interface
  • Auto power saving mode reduces power consumption by 30%
  • Easily locate online clients’ information through the Wireless Location Management
  • System status monitoring includes statistics and associated client list
Ordering Information
WDAP-8350 600Mbps Dual Band 802.11n Outdoor Wireless CPE (IP66, 802.3at PoE, 4 x N-Type connector)
Accessories
CB-STP-25 25-meter STP Cat5 Cable
WL-NM-0.6 0.6-meter N-male (male pin) to N-male (male pin) Cable
ANT-OM5D 2.4/5GHz Dual Band Omni-directional Antenna
ANT-OM8 2.4GHz 8dBi Omni Directional Antenna
ANT-OM15 2.4GHz 15dBi Omni Directional Antenna
ANT-FP9 2.4GHz 9dBi Flat Panel Directional Antenna
ANT-FP14D 2.4GHz 14dBi Flat Panel Dual Polarization Directional Antenna
ANT-FP18 2.4GHz 18dBi Flat Panel Directional Antenna
ANT-SE18 2.4GHz 12-18dBi Adjustable Sector Antenna
ANT-YG13 2.4GHz 13dBi Yagi Directional Antenna
ANT-YG20 2.4GHz 20dBi Yagi Directional Antenna
ANT-GR21 2.4GHz 21dBi Grid Directional Antenna
ANT-OM10A 5GHz 10dBi Omni-directional Antenna
ANT-FP14AD 5GHz 14dBi Flat Panel Dual Polarization Directional Antenna
ANT-FP18A 5GHz 18dBi Flat Panel Antenna
ANT-FP23A 5GHz 23dBi Flat Panel Directional Antenna
ANT-SE17A 5GHz 16.5dBi Sector Antenna
ANT-SE21A 5GHz 21dBi Sector Antenna
Hardware
Interface Wireless: IEEE 802.11n concurrent 2.4GHz and 5GHz, 2T2R MIMO
LAN: 10/100/1000BASE-T, auto-MDI/MDIX, IEEE 802.3at PoE PD
Antenna Built-in 4 N-Type (female) antenna connectors with surge arrestor
※ The outdoor antennas need to be purchased separately
Button/Connector Reset button, ground terminal, ground lug
LED PWR, LAN, 2.4G, 5G
Material Aluminum
Dimensions (W x D x H) 220 x 95 x 220mm
Weight 2.34kg
Power Requirement IEEE 802.3at PoE+
Power Consumption (max.) < 24W (high-loading and heater)
< 7W (power saving mode)
Mounting Type Mast, wall mount
Wireless Interface Specifications
Wireless Standard IEEE 802.11a/n 5GHz
IEEE 802.11b/g/n 2.4GHz
Antenna Structure 802.11n: 2T2R MIMO at each frequency band
Data Rate IEEE 802.11b: 1, 2, 5.5, 11Mbps
IEEE 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54Mbps
IEEE 802.11n (20MHz): up to 150Mbps
IEEE 802.11n (40MHz): up to 300Mbp at each frequency band
Media Access Control CSMA/CA
Modulation Type 802.11a/g/n: OFDM (BPSK/QPSK/16QAM/64QAM)
802.11b: DSSS (DBPSK/DQPSK/CCK)
Band Mode 2.4G and 5G concurrent mode
Frequency Range 2.4GHz: 2.400 ~ 2.484GHz
5GHz: 5.150 ~ 5.850GHz
Operating Channel ■ 2.4GHz
America -- FCC: 1~11
Europe -- ETSI: 1~13

■ 5GHz
America -- FCC:
36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 (total 24 channels)

Europe -- ETSI:
36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 132, 136, 140 (total 16 channels)

※ 5GHz channel list may be vary in different countries and
restricted to abide by regional regulatory compliance.
Channel Width 20MHz/40MHz
Max. RF Power 27dBm for all rate levels and modulation modes
Output Power Control 1 ~ 100%
Software Features
Wireless Mode ■ AP
■ WDS PTP
■ WDS PTMP
Wireless Encryption ■ WEP (64-/128-bit) encryption security
■ WPA/WPA2 (TKIP/AES)
■ WPA-PSK/WPA2-PSK (TKIP/AES)
■ 802.1x authentication
Wireless Advanced Enable/Disable SSID broadcast
Max. associated station number restriction
Multiple SSIDs: up to 16 at 2.4GHz and 16 at 5GHz
Supports multiple VLANs mapping to multiple SSIDs
Supports fast roaming across APs
Provides wireless statistics
Max. Wired Client Unlimited
Max. Wireless Client Theoretical value: 127 at each band
Recommended value: 50 at each band
Max. WDS Peers Up to 16 at 2.4GHz and 16 at 5GHz
QoS Supports multicast rate adaptation mechanism to guarantee the wireless bandwidth and service quality
LAN Static IP, DHCP
IPv4 and IPv6 dual-stack management network
Supports 802.1Q tagged VLAN
System Management Web-based (HTTP) and Telnet command line interface
Supports NTP synchronization
Easy firmware upgrade via HTTP/TFTP
Easy system backup/restore via HTTP/TFTP
Easily locate online clients’ information through the Wireless Location Management
Supports Dual-OS auto-backup mechanism
Supports Auto Power Saving Mode mechanism
Supports PLANET Smart Discovery Utility
Standards Conformance
Standard Compliance IEEE 802.11n (2T2R, dual-N band up to 600Mbps)
IEEE 802.11a
IEEE 802.11g
IEEE 802.11b
IEEE 802.11i
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3ab 1000BASE-T
Other Protocols and Standards CSMA/CA, CSMA/CD, TCP/IP, DHCP, ICMP, SNTP
Environment & Certification
Temperature Operating: -40 ~ 70 degrees C
Storage: -40 ~ 75 degrees C
Humidity Operating: 10 ~ 95% (non-condensing)
Storage: 5 ~ 95% (non-condensing)
IP Level IP66
ESD Protection ±15kV air-gap discharge
±8kV contact discharge
Surge Protection ±6kV line to ground
±2kV line to line
MTBF 1553658 hrs at 25 degrees C
335788 hrs at 60 degrees C
EMC Emissions Class B
Regulatory Compliance CE, FCC, RoHS
Ordering Information
WDAP-8350 600Mbps Dual Band 802.11n Outdoor Wireless CPE (IP66, 802.3at PoE, 4 x N-Type connector)
Accessories
CB-STP-25 25-meter STP Cat5 Cable
WL-NM-0.6 0.6-meter N-male (male pin) to N-male (male pin) Cable
ANT-OM5D 2.4/5GHz Dual Band Omni-directional Antenna
ANT-OM8 2.4GHz 8dBi Omni Directional Antenna
ANT-OM15 2.4GHz 15dBi Omni Directional Antenna
ANT-FP9 2.4GHz 9dBi Flat Panel Directional Antenna
ANT-FP14D 2.4GHz 14dBi Flat Panel Dual Polarization Directional Antenna
ANT-FP18 2.4GHz 18dBi Flat Panel Directional Antenna
ANT-SE18 2.4GHz 12-18dBi Adjustable Sector Antenna
ANT-YG13 2.4GHz 13dBi Yagi Directional Antenna
ANT-YG20 2.4GHz 20dBi Yagi Directional Antenna
ANT-GR21 2.4GHz 21dBi Grid Directional Antenna
ANT-OM10A 5GHz 10dBi Omni-directional Antenna
ANT-FP14AD 5GHz 14dBi Flat Panel Dual Polarization Directional Antenna
ANT-FP18A 5GHz 18dBi Flat Panel Antenna
ANT-FP23A 5GHz 23dBi Flat Panel Directional Antenna
ANT-SE17A 5GHz 16.5dBi Sector Antenna
ANT-SE21A 5GHz 21dBi Sector Antenna

Quick Guide

Date Version Description Download
2015-11-13 1.0 Initial release.
Ordering Information
WDAP-8350 600Mbps Dual Band 802.11n Outdoor Wireless CPE (IP66, 802.3at PoE, 4 x N-Type connector)
Accessories
CB-STP-25 25-meter STP Cat5 Cable
WL-NM-0.6 0.6-meter N-male (male pin) to N-male (male pin) Cable
ANT-OM5D 2.4/5GHz Dual Band Omni-directional Antenna
ANT-OM8 2.4GHz 8dBi Omni Directional Antenna
ANT-OM15 2.4GHz 15dBi Omni Directional Antenna
ANT-FP9 2.4GHz 9dBi Flat Panel Directional Antenna
ANT-FP14D 2.4GHz 14dBi Flat Panel Dual Polarization Directional Antenna
ANT-FP18 2.4GHz 18dBi Flat Panel Directional Antenna
ANT-SE18 2.4GHz 12-18dBi Adjustable Sector Antenna
ANT-YG13 2.4GHz 13dBi Yagi Directional Antenna
ANT-YG20 2.4GHz 20dBi Yagi Directional Antenna
ANT-GR21 2.4GHz 21dBi Grid Directional Antenna
ANT-OM10A 5GHz 10dBi Omni-directional Antenna
ANT-FP14AD 5GHz 14dBi Flat Panel Dual Polarization Directional Antenna
ANT-FP18A 5GHz 18dBi Flat Panel Antenna
ANT-FP23A 5GHz 23dBi Flat Panel Directional Antenna
ANT-SE17A 5GHz 16.5dBi Sector Antenna
ANT-SE21A 5GHz 21dBi Sector Antenna