SGS-6340-24P4S

Layer 3 24-Port 10/100/1000T 802.3at PoE + 4-Port 1000X SFP Stackable Managed Switch (370W)

Powerful Layer 3 Gigabit Routing and Power over Ethernet Solution
PLANET SGS-6340-24P4S is a Layer 3 PoE Stackable Managed Gigabit Switch that provides high-density performance, Layer 3 static routing, RIP (Routing Information Protocol) and OSPF (Open Shortest Path First). With 56Gbps switching fabric, the SGS-6340-24P4S can handle extremely large amounts of data in a secure topology linking to an enterprise backbone or high capacity servers. The powerful WRR (Weighted Round Robin) and Network Security features make the SGS-6340-24P4S perform effective data traffic control for ISP and enterprise VoIP, video streaming, and multicast applications. The SGS-6340-24P4S has 24 IEEE 802.3at PoE+ ports and PoE budget up to 370 watts for catering to medium to large scale of VoIP or IP Surveillance networks at a lower total cost.
Centralized Power Management for Gigabit Ethernet PoE Networking
To fulfill the needs of higher power required PoE network applications with Gigabit speed transmission, the SGS-6340-24P4S features high-performance Gigabit IEEE 802.3af PoE (up to 15.4 watts) and IEEE 802.3at PoE+ (up to 30 watts) on all ports. It perfectly meets the power requirement of PoE VoIP phone and all kinds of PoE IP cameras such as IR, PTZ, speed dome cameras or even box type IP cameras with built-in fan and heater.

The SGS-6340-24P4S’s PoE capabilities also help to reduce deployment costs for network devices as a result of freeing from restrictions of power outlet locations. Power and data switching are integrated into one unit, delivered over a single cable and managed centrally. It thus eliminates cost for additional AC wiring and reduces installation time.

PoE Schedule for Energy Saving
Besides being used for IP surveillance, the SGS-6340-24P4S is certainly applicable to build any PoE network including VoIP and wireless LAN. Under the trend of energy saving worldwide and contributing to the environmental protection on the Earth, the SGS-6340-24P4S can effectively control the power supply besides its capability of giving high watts power. The “PoE schedule” function helps you to enable or disable PoE power feeding for each PoE port during specified time intervals and it is a powerful function to help SMBs or enterprises save energy and budget
Layer 3 Routing Support
The SGS-6340-24P4S enables the administrator to conveniently boost network efficiency by configuring Layer 3 static routing manually, the RIP (Routing Information Protocol) or OSPF (Open Shortest Path First) settings automatically. The RIP can employ the hop count as a routing metric and prevent routing loops by implementing a limit on the number of hops allowed in a path from the source to a destination. The maximum number of hops allowed for the RIP is 15. The OSPF is an interior dynamic routing protocol for autonomous system based on link-state. The protocol creates a link-state database by exchanging link-states among Layer 3 switches, and then uses the Shortest Path First algorithm to generate a route table based on that database.

Abundant IPv6 Support
The SGS-6340-24P4S provides IPv6 management and enterprise-level secure features such as SSH, ACL, WRRand RADIUS authentication. The SGS-6340-24P4S thus helps the enterprises to step in the IPv6 era with the lowest investment. In addition, you don’t need to replace the network facilities when the IPv6 FTTx edge network is built.

High Performance
The SGS-6340-24P4S boasts a high-performance switch architecture that is capable of providing non-blocking switch fabric and wire-speed throughput as high as 56Gbps, which greatly simplifies the tasks of upgrading the LAN for catering to increasing bandwidth demands.
Robust Layer 2 Features
The SGS-6340-24P4S can be programmed for basic switch management functions such as port speed configuration, port aggregation, VLAN, Spanning Tree Protocol, WRR, bandwidth control and IGMP snooping. The SGS-6340-24P4S provides 802.1Q tagged VLAN, Q-in-Q, voice VLAN and GVRP Protocol. The VLAN groups allowed to be on the SGS-6340-24P4S will be maximally up to 256. By supporting port aggregation, the SGS-6340-24P4S allows the operation of a high-speed trunk combined with multiple ports. It enables up to 128 groups for trunking with a maximum of 8 ports for each group.

Excellent Traffic Control
The SGS-6340-24P4S is loaded with powerful traffic management and WRR features to enhance services offered by telecoms. The WRR functionalities include wire-speed Layer 4 traffic classifiers and bandwidth limitation which are particularly useful for multi-tenant unit, multi-business unit, Telco, or network service applications. It also empowers the enterprises to take full advantage of the limited network resources and guarantees the best performance in VoIP and video conferencing transmission.

Powerful Security
The SGS-6340-24P4S supports ACL policies comprehensively. The traffic can be classified by source/destination IP addresses, source/destination MAC addresses, IP protocols, TCP/UDP, IP precedence, time ranges and ToS. Moreover, various policies can be conducted to forward the traffic. The SGS-6340-24P4S also provides IEEE 802.1x port based access authentication, which can be deployed with RADIUS, to ensure the port level security and block illegal users.

Efficient Management
The SGS-6340-24P4S supports IP stacking function that helps network managers to easily configure up to 24 switches in the same series via one single IP address instead of connecting and setting each unit one by one. For efficient management, the SGS-6340-24P4S Managed Gigabit Switch is equipped with console, Web and SNMP management interfaces. With its built-in Web-based management interface, the SGS-6340-24P4S offers an easy-to-use, platform-independent management and configuration facility. The SGS-6340-24P4S supports standard Simple Network Management Protocol (SNMP) and can be managed via any standard-based management software. For text-based management, the SGS-6340-24P4S can be accessed via Telnet and the console port. Moreover, the SGS-6340-24P4S offers secure remote management by supporting SSH connection which encrypts the packet content at each session.

Flexibility and Extension Solution
The four mini-GBIC slots built in the SGS-6340-24P4S are compatible with 1000BASE-X and WDM SFP (Small Form-factor Pluggable) fiber-optic modules. The distance can be extended from 550 meters (multi-mode fiber) to 10/50/70/120 kilometers (single-mode fiber or WDM fiber). They are well suited for applications within the enterprise data centers and distributions.
Ordering Information
SGS-6340-24P4S Layer 3 24-Port 10/100/1000T 802.3at PoE + 4-Port 1000X SFP Stackable Managed Switch (370W)
High Scalability & Best Security for Today’s IP Networking and Cyber Security Solution
The SGS-6340-24P4S comes with non-blocking design and SFP fiber-optic modules, bringing network infrastructure higher flexibility but lower in cost. Providing twenty-four 10/100/1000BASE-T PoE+ ports and four Gigabit SFP ports, the SGS-6340-24P4S can easily build a secure network on the cyber security system for the enterprises. For instance, it can work with the router and UTM to perform comprehensive security protection for today’s businesses.
Layer 3 VLAN Routing
With the built-in robust Layer 3 traffic routing protocols, the SGS-6340-24P4S ensures reliable routing between VLANs and network segments. The routing protocols can be applied via VLAN interface. The SGS-6340-24P4S is certainly a cost-effective and ideal solution for enterprises.
Ordering Information
SGS-6340-24P4S Layer 3 24-Port 10/100/1000T 802.3at PoE + 4-Port 1000X SFP Stackable Managed Switch (370W)
Physical Ports
  • 24-Port 10/100/1000BASE-T Gigabit Ethernet RJ45 with 24-port IEEE 802.3at/af PoE injector
  • 4 1000BASE-X mini-GBIC/SFP slots
  • RJ45 to DB9 console interface for switch basic management and setup

Power over Ethernet
    • Complies with IEEE 802.3at Power over Ethernet Plus, end-span PSE
    • Backward compatible with IEEE 802.3af Power over Ethernet
    • Up to 24 ports of IEEE 802.3af/802.3at devices powered
    • Supports PoE power up to 30 watts for each PoE port
    • Auto detects powered device (PD)
    • Circuit protection prevents power interference between ports
    • Remote power feeding up to 100 meters
    • PoE management
- Total PoE power budget control- Per port PoE function enable/disable- PoE port power feeding priority- Per PoE port power limitation- PD classification detection- PoE schedule
IP Stacking
  • Connects with stack member via both Gigabit TP and SFP interfaces
  • Single IP address management, supporting up to 24 units stacked together

IP Routing Features
  • Supports maximum 128 static routes and route summarization
  • Supports dynamic routing protocol: RIP and OSPF

Layer 2 Features
    • Complies with the IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z Gigabit Ethernet standard
    • Supports auto-negotiation and half-duplex/full-duplex modes for all 10BASE-T, 100BASE-TX and 1000BASE-T ports
    • Auto-MDI/MDI-X detection on each RJ45 port
    • Prevents packet loss flow control
- IEEE 802.3x pause frame flow control in full-duplex mode- Back-pressure flow control in half-duplex mode
    • High performance Store-and-Forward architecture, broadcast storm control, port loopback detect
    • 16K MAC address table, automatic source address learning and aging
    • Supports VLAN
- IEEE 802.1Q tag-based VLAN- GVRP for dynamic VLAN management- Up to 256 VLANs groups, out of 4041 VLAN IDs- Provider Bridging (VLAN Q-in-Q, IEEE 802.1ad) supported- Private VLAN Edge (PVE) supported- GVRP protocol for Management VLAN- Protocol-based VLAN- MAC-based VLAN- IP subnet VLAN
    • Supports Link Aggregation
- Maximum 128 trunk groups, up to 8 ports per trunk group- IEEE 802.3ad LACP (Link Aggregation Control Protocol)- Cisco ether-channel (static trunk)
    • Supports Spanning Tree Protocol
- STP, IEEE 802.1D (Classic Spanning Tree Protocol)- RSTP, IEEE 802.1w (Rapid Spanning Tree Protocol)- MSTP, IEEE 802.1s (Multiple Spanning Tree Protocol, spanning tree by VLAN)- Supports BPDU & root guard
  • Port mirroring to monitor the incoming or outgoing traffic on a particular port (many to many)
  • Provides port mirror (many-to-1)

Quality of Service
    • 8 priority queues on all switch ports
    • Support for strict priority and WRR (Weighted Round Robin) CoS policies
    • Traffic classification
- IEEE 802.1p CoS/ToS- IPv4/IPv6 DSCP- Port-based WRR
  • Strict priority and WRR CoS policies

Multicast
  • Supports IPv4 IGMP snooping v1, v2 and v3, IPv6 MLD v1 and v2 snooping
  • Querier mode support
  • Supports Multicast VLAN Register (MVR)

Security
  • IEEE 802.1x port-based network access authentication
  • MAC-based network access authentication
  • Built-in RADIUS client to co-operate with the RADIUS servers for IPv4 and IPv6
  • TACACS+ login users access authentication
  • IP-based Access Control List (ACL)
  • MAC-based Access Control List
  • Supports DHCP snooping
  • Supports ARP inspection
  • IP Source Guard prevents IP spoofing attacks
  • Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding

Management
    • Management IP for IPv4 and IPv6
    • Switch Management Interface
- Console/Telnet Command Line Interface- Web switch management- SNMP v1, v2c, and v3 switch management- SSH/SSL secure access
  • BOOTP and DHCP for IP address assignment
  • Firmware upload/download via TFTP or HTTP Protocol for IPv4 and IPv6
  • SNTP (Simple Network Time Protocol) for IPv4 and IPv6
  • User privilege levels control
  • Syslog server for IPv4 and IPv6
  • Four RMON groups 1, 2, 3, 9 (history, statistics, alarms and events)
  • Supports ping, trace route function for IPv4 and IPv6
Ordering Information
SGS-6340-24P4S Layer 3 24-Port 10/100/1000T 802.3at PoE + 4-Port 1000X SFP Stackable Managed Switch (370W)
Hardware Specifications
Copper Ports 24 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports
SFP/mini-GBIC Slots 4 1000BASE-X SFP interfaces
PoE Injector Port 24 ports with 802.3at/af PoE injector function with port-1 to port-24
Console 1 x RJ45-to-RS232 serial port (9600, 8, N, 1)
Switch Architecture Store-and-forward
Switch Fabric 56Gbps/non-blocking
Switch Throughput 41.66Mpps
Address Table 16K MAC address table with auto learning function
Shared Data Buffer 1.5MB
Flow Control Back pressure for half-duplex
IEEE 802.3x pause frame for full-duplex
Jumbo Frame 9KB
LED System:
PWR, SYS
Ports:
10/100/1000T RJ45 Port: Button off: LNK/ACT, Button on: PoE In-Use
1000X SFP slot: LNK/ACT
Dimensions (W x D x H) 442 x 330 x 44 mm, 1U height
Weight 4503g
Power Consumption 449 watts/1532.05 BTU (maximum)
Power Requirements AC 100~240V, 50/60Hz
Fan 3
Power over Ethernet
PoE Standard IEEE 802.3af/802.3at PoE+ PSE
PoE Power Supply Type End-span
PoE Power Output Per port 54V DC, 33 watts (max.)
Power Pin Assignment 1/2(+), 3/6(-)
PoE Power Budget 370 watts (max.)
PoE Ability PD @ 9 watts 24 units
PoE Ability PD @ 15 watts 24 units
PoE Ability PD @ 30 watts 12 units
Management Function
System Configuration Console, Telnet, SSH, Web browser, SNMP v1, v2c and v3
Management Supports both IPv4 and IPv6 addressing
Supports the user IP security inspection for IPv4/IPv6 SNMP
Supports MIB and TRAP
Supports IPv4/IPv6 FTP/TFTP
Supports IPv4/IPv6 NTP
Supports RMON 1, 2, 3, 9 four groups
Supports the RADIUS authentication for IPv4/IPv6 Telnet user name and password
Supports IPv4/IPv6 SSH
The right configuration for users to adopt RADIUS server’s shell management
Supports CLI, console, Telnet
Supports SNMP v1, v2c and v3
Supports Security IP safety net management function: avoid unlawful landing at nonrestrictive area
Supports Syslog server for IPv4 and IPv6
Supports TACACS+
Layer 3 Function
Routing Protocol Static routing, RIP and OSPF
Routing Table 128
Layer 2 Function
Port Configuration Port disable/enable
Auto-negotiation 10/100/1000Mbps full and half duplex mode selection
Flow control disable/enable
Bandwidth control on each port
Port loopback detect
Port Status Display each port’s speed duplex mode, link status, flow control status and
auto negotiation status
VLAN 802.1Q tagged based VLAN, up to 256 VLAN groups
802.1ad Q-in-Q (VLAN stacking)
GVRP for VLAN management
Private VLAN Edge (PVE) supported
Protocol-based VLAN
MAC-based VLAN
IP subnet VLAN
Bandwidth Control TX/RX/both
Link Aggregation IEEE 802.3ad LACP/static trunk
Supports 128 groups with 8 ports per trunk group
QoS 8 priority queues on all switch ports
Supports strict priority and Weighted Round Robin (WRR) CoS policies
Traffic classification:
- IEEE 802.1p CoS/ToS
- IPv4/IPv6 DSCP
- Port-based WRR
Multicast IGMP v1/v2/v3 snooping
Querier mode support
MLD v1/v2 snooping
Querier mode support
Multicast VLAN Register (MVR)
Access Control List Supports Standard and Expanded ACL
IP-based ACL/MAC-based ACL
Time-based ACL
Up to 512 entries
Bandwidth Control At least 64Kbps step
Security Supports MAC + port binding
IPv4/IPv6 + MAC + port binding
IPv4/IPv6 + port binding
Supports MAC filter
ARP scanning prevention
Authentication IEEE 802.1x port-based network access control
AAA authentication: TACACS+ and IPv4/IPv6 over RADIUS
SNMP MIBs RFC 1213 MIB-II
RFC 1215 Internet Engineering Task Force
RFC 1271 RMON
RFC 1354 IP-Forwarding MIB
RFC 1493 Bridge MIB
RFC 1643 Ether-like MIB
RFC 1907 SNMP v2
RFC 2011 IP/ICMP MIB
RFC 2012 TCP MIB
RFC 2013 UDP MIB
RFC 2096 IP forward MIB
RFC 2233 if MIB
RFC 2452 TCP6 MIB
RFC 2454 UDP6 MIB
RFC 2465 IPv6 MIB
RFC 2466 ICMP6 MIB
RFC 2573 SNMP v3 notify
RFC 2574 SNMP v3 vacm
RFC 2674 Bridge MIB Extensions
Standard Conformance
Regulatory Compliance FCC Part 15 Class A, CE
Standards Compliance IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3z Gigabit 1000BASE-SX/LX
IEEE 802.3ab Gigabit 1000BASE-T
IEEE 802.3x flow control and back pressure
IEEE 802.3ad port trunk with LACP
IEEE 802.1D Spanning Tree Protocol
IEEE 802.1w Rapid Spanning Tree Protocol
IEEE 802.1s Multiple Spanning Tree Protocol
IEEE 802.1p Class of Service
IEEE 802.1Q VLAN tagging
IEEE 802.1X port authentication network control
IEEE 802.1ab LLDP
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet PLUS
RFC 768 UDP
RFC 793 TFTP
RFC 791 IP
RFC 792 ICMP
RFC 2068 HTTP
RFC 1112 IGMP v1
RFC 2236 IGMP v2
RFC 3376 IGMP v3
RFC 2710 MLD v1
FRC 3810 MLD v2
RFC 2328 OSPF v2
RFC 1058 RIP v1
RFC 2453 RIP v2
Environment
Operating Temperature: 0 ~ 50 degrees C
Relative Humidity: 5 ~ 90% (non-condensing)
Storage Temperature: -10 ~ 70 degrees C
Relative Humidity: 5 ~ 90% (non-condensing)
Ordering Information
SGS-6340-24P4S Layer 3 24-Port 10/100/1000T 802.3at PoE + 4-Port 1000X SFP Stackable Managed Switch (370W)

Datasheet

Date Version Description Download
2015-08-21 1.0 SGS-6340-24P4S

Quick Guide

Date Version Description Download
2015-08-07 1.0 Initial release.

User's Manual

Date Version Description Download
2015-09-21 1.0 Initial release for Command Guide.
2015-09-18 1.0 Initial release for Configuration Guide.
Ordering Information
SGS-6340-24P4S Layer 3 24-Port 10/100/1000T 802.3at PoE + 4-Port 1000X SFP Stackable Managed Switch (370W)